MXR

• Separate INPUT & OUTPUT level controls
• 3-band EQ section with sweepable midrange
• Studio-quality Direct Out

• Overdrive pedal made exclusively for bass
• Get big, punchy, tubelike bass tone
• Volume, Tone, and Drive controls
• Clean control lets you blend your clean signal in with the overdrive
• Compact, pedalboard-friendly form factor
• Powered by one 9V battery or AC adapter (not included)

• Vintage Echoplex EP-3 tape echo warmth and modulation
• Audiophile quality audio paths
• 100% analog dry path
• Studio-grade low noise floor
• Age control varies delay tone from pristine to dark and dirty
• Delay control provides 65–750ms of delay time
• Tap jack provides up to 4 seconds of delay time with external Tap Tempo Switch
• The Echoplex Delay requires 9 volts (240mA) and can be powered by the included Dunlop ECB003/ECB003EU adapter or the Iso-Brick ™ Power Supply. This pedal cannot be powered by a battery.
• To combine the EP103 with the EP101 Echoplex Preamp for the full Echoplex EP-3 experience, simply run the EP101 in front of the EP103

• Hand-wired circuit board built with original-spec 1974 components
• Warm analog tone
• Select resistors paired with hand-matched FETs
• Adorned with script logo
• Simple one-knob operation
• Deep, rich phasing

• Classic studio compressor in a Phase 90-sized pedal
• CHT™ Constant Headroom
• Technology for clear, clean performance
• Ten Gain Reduction status LEDs
• True bypass
• The MXR Studio Compressor is powered by one 9-volt battery (remove bottom plate to install), a 9-volt AC adapter such as the Dunlop ECB003/ECB003EU, or the DC Brick™ and Iso-Brick™ power supplies.

• Compact chorus effect pedal
• All-analog circuitry with bucket-brigade technology
• Offers a wide range of rich chorus textures
• True-bypass circuitry keeps your tone intact

Every effect a bass player could ever need in one compact box: distortion channel with gain, volume and blend controls; noise gate switch with trigger control. The clean channel features a colour switch with bass, mid and treble controls. 

• Versatile signal switching to multiple amps, with different effects configurations
• Thru output for a constant signal
• Heavy duty housing

Adds dimension and dynamics to Zakk's legendarily blazing solos and razor sharp leads; all with the twist of a single rate knob. Take it from a slow grind to a jack hammering pulse, or use it as Zakk does, at the 9 o'clock position for a slow burning sweep. Jack your tone into another dimension.
Hardwire bypass. Powered by 9 volt battery or AC adaptor.

• 100HZ cut and boost control allows tonal fine-tuning
• BUMP switch engages alternate voicing for a low and mid-range boost
• True Bypass

• Wet and dry controls let you mix your tone to taste
• Designed to preserve the fundamental spunch & clarity of your bass
• Unique distortion circuitry based on a modified fuzz pedal

• Combines La Machine Fuzz with old school Sub-Octave signal
• Separate volume levels for Fuzz and Sub-Octave signals
• Toggle between Series/Parallel modes
• Octave switch kicks Fuzz signal into Octave Up mode
• The Sub Machine Fuzz is powered by one 9-volt battery (remove bottom plate to install), a 9-volt AC adapter such as the Dunlop ECB003/ECB003EU, or the DC Brick™ and Iso-Brick™ power supplies.

• Four different parameters for precise fine-tuning
• EVH switch engages “Unchained” flanger tone
• Custom EVH paint job
• The EVH Flanger is powered by two 9 volt batteries (accessed through the bottom of the pedal), an 18 volt AC adapter such as the Dunlop ECB004/ECB004EU, or a DC Brick™ power supply.

• Delivers everything from overdrive to distortion
• Natural, amp-like distortion
• Retains your guitar's tone and clarity